AT24CO4

A 4K x 8 (32K bit) Serial Electrically Erasable PROM is the 24C32. This gadget was created for high-end, low-power uses like data collecting or personal communications. The 24C32 has an input cache with a capacity of eight 8-byte pages, or 64 bytes, allowing quick write loads. Additionally, it has a fixed 4K-bit block of ultra-high endurance memory for regularly changing data. Up to the 32K border, the 24C32 may read both randomly and sequentially. Up to eight 24C32 devices can share a bus with functional address lines, providing a maximum address space of 256K bits. This device is perfect for moderate POWER??non-volatile code and data applications thanks to advanced CMOS technology. The typical 8-pin plastic DIP and 8-pin surface mount SOIC packaging for the 24C32 are also available.   Features:- ? Operating voltage range: 4.5V to 5.5V - Maximum read current: 150 A at 5.5V - Peak write current: 3mA at 5.5V - Typical standby current: 1 A ? I2C compliant, industry-standard two-wire bus protocol with 100 kHz and 400 kHz modes ? Autonomous write cycle (including auto-erase) ? Switchable circuitry for data protection ? High Endurance Block has a guaranteed 10,000,000 Erase/Write cycles. - Guaranteed 1,000,000 E/W cycles for Standard Endurance Block ? Available in 8 byte page or byte modes. ? A 64-byte input cache with 1 page by 8 lines for quick write loads. ? Schmitt trigger with filtered inputs to reduce noise ? Ground bounce elimination by output slope control ? A typical write cycle time, byte or page, of 2 ms ? A single bus may support up to 8 chips and 256K bits of total memory. ? Protection from electrostatic discharge > 4000V ? 200-year data retention ? PDIP/SOIC 8-pin packages ? Variable temperatures Industrial (I): -40?C to +85?C Commercial (C): 0?C to +70?C

The Microchip Technology Inc. 25AA320/25LC320/25C320 (25XX320*) serial Electrically Erasable PROMs are 32 Kbit. A basic Serial Peripheral Interface (SPI) compliant serial bus is used to access the memory. A clock input (SCK) is required, as well as separate data in (SI) and data out (SO) lines. A Chip Selection (CS) input controls access to the device. The hold pin allows you to suspend communication with the gadget (HOLD). Transitions on the device's inputs will be ignored while it is stopped, excluding Chip Select, enabling the host to service higher priority interrupts. Features ? CMOS Low-Power Technology: - Maximum write current: 3 mA - Typical read current: 500 A - Typical standby current: 500 nA ? 4096 x 8 Bit Storage ? 32 bytes each page ? Maximum Write Cycle Time: 5 ms ? Erase and write cycles that are self-timed ? Write Block Protection: - Protect none, 1/4, 1/2, or the entire array. ? Integrated Write Protection: - Data protection circuitry that is switched on and off ? Latch for write enable - A write-protection pin ? Read in Sequence ? High dependability: - Endurance: 1 million E/W cycles - Data retention: more than 200 years - ESD protection: more than 4000V ? PDIP, SOIC, and TSSOP packages with 8 pins ? TSSOP Package with 14 Leads

A CMOS 8-bit microcontroller with 20K bytes of Flash programmable read-only memory and 256 bytes of RAM, the AT89C55WD is a low-power, high-performance device. The product is made using high-density flash storage technology from Atmel and has pinout and an instruction set that comply with industry standards 80C51 and 80C52. An ordinary nonvolatile memory programmer can user programme the programme memory thanks to the on-chip Flash. The Atmel AT89C55WD is a potent microcomputer that offers a very flexible and area of business to many embedded control applications by mixing a flexible 8-bit CPU with Flash on a monolithic chip. The following features are included as standard with the AT89C55WD: A full-duplex serial port, an on-chip oscillator, clock circuitry, three 16-bit timer/counters, 32 I/O lines, 256 bytes of RAM, 20K bytes of Flash, and a six-vector, two-level interrupt architecture. The AT89C55WD also features two software-selectable power-saving modes and static logic allowing operating down to zero frequency. The CPU is turned off in idle mode, but the RAM, timers and counters, serial port, and interruption system are still operational. The oscillator is frozen in the Power-down Mode, which also disables all other chip operations until the next error detection or device reset. However, the RAM contents are saved.

Features? of M24128-DRD

• Support for all I2C bus modes? 1 MHz/ 400 kHz/ 100 kHz
• Memory bank- An EEPROM with 128 Kbits (16 Kbytes)
• Page Size in Bytes: 64
• In addition Make a locked page.
• Wider range of temperatures and voltages?40 to 105 degrees Celsius; 1.7 to 5.5 volts
• Schmitt trigger inputs are used to filter noise.
• Cycle time for short writes- Byte Write in 4 milliseconds- Page Write in 4 milliseconds
• Express cycling stamina. -4,000,000 Write Cycles at 25 ?C, - 1,2,000,000 Write cycles at 85 ?C & ? 900 k Cycles of writing at 105 ?C
• Data storage- at 105 ?C for more than 50 years., 200 yr at 55 ?C
• ESD Defense (Human Body Model)? 4000 V
• Packing is- Halogen-free and RoHS compliant

Characteristics of M24128-DRD

• SMD/SMT mounting style
• Case/Package: TSSOP-8
• Interface types: I2C and 2-Wire
• Size of Memory: 128 kbit
• Arrangement: 16 k x 8
• Minimum Supply Voltage: 1.7 V
• Maximum Supply Voltage: 5.5 V
• 40 C for the minimum operating temperature
• 105 C is the maximum operating temperature.
• 1 MHz is the maximum clock frequency.
• Time to Access: 450 ns
• Retention of Data: 200 Years
• Maximum Supply Current: 2 mA
• The M24128-DRD series
• mandatory requirement: AEC-Q100
• Packaging: Cut Tape and Reel
• Maximum Active Read Current: 2 mA
• STMicroelectronics is a brand.
• 2 mA is the operating supply current.
• Voltage Range for Operating Supply: 1.8 to 5.5 V
• Type of Product: EEPROM