MAX485ESA RS422 RS485 Interface IC
₹93.00
MAX485 is a low power transceivers for RS485 and RS422 communication. MAX485 contains one driver and one receiver. The driver slew rates of the MAX485 are not limited, allowing it to transmit up to 2.5Mbps.
These transceivers draw between 120?A and 500?A of supply current when unloaded or fully loaded with disabled drivers.?MAX485ESA RS422 RS485 IC?operates from a single 5V supply. Drivers are short circuit current limited and are protected against excessive power dissipation by thermal shutdown circuitry that places the driver outputs into a high-impedance state. The receiver input has a fail-safe feature that guarantees a logic-high output if the input is open circuit.
1000 in stock (can be backordered)
Reviews (0)
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
AM26C31 Differential Line Receiver (SOIC)
The AM26C31 is an improved replacement for?AM26LS31 IC.?The AM26C31 device is a quadruple differential line receiver for balanced or unbalanced digital data transmission. The enable function is common to all four receivers and offers a choice of active-high or active-low input. The 3-state outputs permit connection directly to a busorganized system. Fail-safe design specifies that if the inputs are open, the outputs always are high. The AM26C31 devices are manufactured using a BiCMOS process, which is a combination of bipolar and CMOS transistors
CH340g USB to TTL IC
As of now the CH340g is the cheapest USB to TTL IC in the market with very easy to solder foot print it has solder pitch of 1.27mm and SOIC16 package.
The?CH340 IC?does exactly what you would expect them to do: a full-speed USB device that emulates a standard serial interface, with speeds from 50bps to 2Mpbs. The chip supports 5V and 3.3V, and all the weird modem lines are supported.
Now a days lots of Node MCU, Arduino Nano and USB to TTL Converter Modules have been using this IC.
CM8870-PI
The CM8870PI provides full DTMF receiver capability by integrating both the bandsplit filter and digital decoder functions into a single 18-pin DIP. The filter section uses a switched capacitor technique for both high and low group filters and dial tone rejection. The CM8870 decoder uses digital counting techniques for the detection and decoding of all 16 DTMF tone pairs into a 4-bit code. This DTMF receiver minimizes external component count by providing an on-chip differential input ampli-fier, clock generator, and a latched three state interface bus. The on-chip clock generator requires only a low cost TV crystal or ceramic resonator as an external component.
CP2103 USB to TTL Converter
The CP2103 is a highly-integrated?USB-to-UART Bridge Controller?providing a simple solution for updating RS-232/RS-485 designs to USB using a minimum of components and PCB space. The CP2103 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, EEPROM, and asynchronous serial data bus (UART) with full modem control signals in a compact 5x5 mm QFN-28 package (sometimes called ?MLF? or ?MLP?). No other external USB components are required.
Reviews
There are no reviews yet.