Benefits and features of BGU7005

• Covers the entire GNSS L1 range, 1559 to 1610 MHz
• Noise figure (NF) is equal to 0.85 dB.
• Increase 16.5 dB
• A lot of input Pi(1dB), or 1 dB compression point, is 11 dBm.
• High IP3i out of band of 9 dBm
• 1.5 to 3.1 volts is the supply voltage.
• Consumption of current in power-saving mode is 1 A.
• Optimized performance at 4.5 mA, a low supply current
• Output matching that is integrated
• Only needs one supply decoupling capacitor and one input matching inductor.
• Decoupled DC input and output
• All pins have ESD protection (HBM > 2 kV).
• Temperature-stabilized bias included for simple design
• Small leadless 6-pin package 1.45 mm, 1 mm, and 0.5 mm
• Transit frequency of 110 GHz using SiGe:C technology

Features of CC2592

• LNA Gain Digitally Controlled via an HGM Terminal  
• (LNA EN = PA EN = 0) 100 nA in Power Down  
• Little Transmit Current Use -PAE = 34% at -155 mA at 3 V for +22 dBm  
• Low Receiving Current Intake -For High-Gain Mode, use -4.0 mA -For Low-Gain Mode, -1.9 mA  
• T/R Switch and External Antenna Match Included in the 4.7-dB LNA Noise Figure  
• Conforms to RoHS QFN-16 Package, 4-mm by 4-mm  
• Operation from 2.0-V to 3.7-V  
• Operating Range: -40?C to +125?C
• Texas Instruments' Seamless Interface to 2.4-GHz Low-Power RF Devices  
• Power Output: +22 dBm  
• Improved Sensitivity of 3 dB Typically on CC2520, CC253X, and CC85XX  
• Almost No External Components -Switches that are built-in -Network for Integrated Matching -Balun integrated -Integral Inductors -Integration of PA -LNA integrated

  Applications? of CC2592  

• Every 2.4-GHz ISM Band Device
• Gateways for ZigBee and IEEE 802.15.4
• Sensor Networks, Wireless
• Consumer Wireless Systems
• Industrial Wireless Systems
• Systems for Wireless Audio
• Metering systems utilizing IEEE 802.15.4 and ZigBee?

HT12D is a decoder integrated circuit that belongs to 212 series of decoders. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. It is mainly provided to interface RF and infrared circuits.? They are paired with 212 series of encoders. The chosen pair of encoder/decoder should have same number of addresses and data format.In simple terms, HT12D converts the serial input into parallel outputs. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. The serial input data is compared with the local addresses three times continuously. The input data code is decoded when no error or unmatched codes are found. A valid transmission in indicated by a high signal at VT pin. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. The data on 4 bit latch type output pins remain unchanged until new is received. Datasheet of ht12d decoder ic

Features? of? L30960-N5130-B100

• LTE (2x2 DL-MIMO; FDD 3GPP Release 9)
• 3GPP Release 8; UMTS/HSPA (FDD); Rx diversity
• 3GPP Release 6; DARP/SAIC; GSM/GPRS/EDGE
• SIM Application Toolkit, version 99 of the 3GPP
• Using AT instructions to control (Hayes, TS 27.007, TS 27.005)
• 3.3 to 4.2 V supply voltage range, especially tuned for low power usage
• Size: 40, 32, and 2,8 mm
• Range of Operation Temperature: -40 ?C to +95 ?
• Compliant with RoHS, RED, and REACH, EuP assistance

  Special Features L30960-N5130-B100

• The USB 2.0/3.0 interface provides several composite modes and a mode that is compatible with Linux and Mac.
• USB-based firmware update

 

The MT8870 is a complete DTMF receiver integrating both the bandsplit filter and digital decoder functions. The filter section uses switched capacitor techniques for high and low group filters; the decoder uses digital counting techniques to detect and decode all 16 DTMF tone-pairs into a 4-bit code.