LPC1768 Microcontrollers – MCU
₹1,500.00
CPU frequencies of up to 100 MHz are supported by the LPC1768/67/66/65/64/63. The LPC1769 can run at CPU speeds of up to 120 MHz. The Arm Cortex-M3 CPU has a three-stage pipeline and a Harvard architecture, with separate local instruction and data buses and a third bus for peripherals. An inbuilt prefetch unit that facilitates speculative branching is also included in the Arm Cortex-M3 CPU.The LPC1769/68/67/66/65/64/63’s peripheral complement includes up to 512 kB of flash memory, 64 kB of data memory, Ethernet MAC, USB Device/Host/OTG interface, 8-channel general-purpose DMA controller, 4 UARTs, 2 CAN channels, 2 SSP controllers, SPI interface, 3 I2C-bus interfaces, 2-input plus 2-output I2S-bus interface, 8-channel 12-bit A
Description
Features – LPC1768 Microcontrollers – MCU
- Arm??Cortex-M3 processor, running at frequencies of up to 100 MHz
- Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
- Up to 512 kB on-chip flash programming memory
- Up to 64 kB On-chip SRAM
- In-System Programming (ISP) and In-Application Programming (IAP)
- Eight-channel General-Purpose DMA controller (GPDMA)
- Ethernet MAC with RMII interface and dedicated DMA controller
- USB 2.0 full-speed device/Host/OTG controller
- Four UARTs with fractional baud rate generation, internal FIFO, and DMA support
- CAN 2.0B controller with two channels
- SPI controller with synchronous, serial, full-duplex communication
- Two SSP controllers with FIFO and multi-protocol capabilities
- Three enhanced I2C bus interfaces
- I2S (Inter-IC Sound) interface
- 70 General Purpose I/O (GPIO) pins with configurable pull-up/down resistors
- 12-bit/8-ch Analog/Digital Converter (ADC) with conversion rates up to 200 kHz
- 10-bit Digital/Analog Converter (DAC) with dedicated conversion timer and DMA
- Four general-purpose timers/counters
- One motor control PWM with support for three-phase motor control
- Quadrature encoder interface that can monitor one external quadrature encoder
- One standard PWM/timer block with external count input
- Low power RTC with a separate power domain and dedicated oscillator
- Watchdog Timer (WDT)
- Arm Cortex-M3 system tick timer, including an external clock input option
- Repetitive interrupt timer provides programmable and repeating timed interrupts
- Each peripheral has its own clock divider for further power savings
- Standard JTAG test/debug interface for compatibility with existing tools
- Integrated PMU (Power Management Unit)
- Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down
- Single 3.3 V power supply (2.4 V to 3.6 V)
- Four external interrupt inputs configurable as edge/level sensitive
- Non-maskable Interrupt (NMI) input
- Wake-up Interrupt Controller (WIC)
- Processor wake-up from Power-down mode via any interrupt
- Brownout detect with separate threshold for interrupt and forced reset
- Power-On Reset (POR)
- Crystal oscillator with an operating range of 1 MHz to 25 MHz
- 4 MHz internal RC oscillator trimmed to 1 % accuracy
- Code Read Protection (CRP) with different security levels
- Unique device serial number for identification purposes
Target Applications – LPC1768 Microcontrollers – MCU
- eMetering
- Lighting
- Industrial networking
- Alarm systems
- White goods
- Motor control
Reviews (0)
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
APQ8009-0-504NSP-TR-01-1-AA
Features of APQ8009
- Adreno 304 GPU 3D graphics accelerator with support for the newest API (up to 456 MHz)
- Battery-friendly audio/video use cases are provided by the Hexagon 536 DSP.
- Heterogeneous architecture features a quad-core, 32-bit Arm Cortex-A7 CPU with a maximum clock speed of 1.3GHz.
- Made using the cutting-edge 28 nm LP CMOS manufacturing method
- Integrated Bluetooth 4.1 low energy, GPS, and 802.11a/b/g/n support
- Offers specialized support for popular codecs in the market as well as additional multimedia formats to enable carrier deployments worldwide.
- An international network of QTI suppliers, users, programmers, and embedded device OEMs
- Wireless Speakers
- Cellular cameras
- Audiovisual Equipment
- Smart home technology
- Smart Home Devices
- Digital helpers
ATMEGA32A-PU Microcontroller
ATMEGA32A-PU Microcontroller is a low-power, CMOS 8-bit microcontroller based on the AVR? enhanced RISC architecture. The ATmega32A is a 40/44-pin device with 32 KB Flash, 2 KB SRAM and 1 KB EEPROM. By executing instructions in a single clock cycle, the devices achieve CPU throughput approaching one million instructions per second (MIPS) per megahertz, allowing the system designer to optimize power consumption versus processing speed.
ATMEGA32A-PU Microcontroller - Specifications
- Manufacturer - MICROCHIP (ATMEL)
- Part Number - ATMEGA32A-PU
- Type of integrated circuit - AVR microcontroller
- Description - 8 Bit Microcontrollers - MCU
- Number of Pins - 40
- Datasheet - ATmega32A-PU Datasheet
LM324 Low Power Quad Op-Amp IC DIP-14
The LM324IC series are low?cost, quad operational amplifiers with true differential inputs. They have several distinct advantages over
standard operational amplifier types in single supply applications. The quad amplifier can operate at supply voltages as low as 3.0 V or as high as 32 V with quiescent currents about one?fifth of those associated with the MC1741 (on a per amplifier basis). The common-mode input range includes the negative supply, thereby eliminating the necessity for external biasing components in many applications. The
output voltage range also includes the negative power supply voltage.
MCP3202-BI/P
MCP3202 is a successive approximation 12-bit analog-to-digital (A/D) converter with on-board sample and hold circuitry. The MCP3202 is programmable to provide a single pseudo-differential input pair or dual single-ended inputs. Differential Nonlinearity (DNL) is specified at ?1 LSB, and Integral Nonlinearity (INL) is offered in ?1 LSB (MCP3202-B) and ?2 LSB (MCP3202-C) versions.
Communication with the device is done using a simple serial interface compatible with the SPI protocol. The device is capable of conversion rates of up to 100 ksps at 5V and 50 ksps at 2.7V. The MCP3202 operates over a broad voltage range, 2.7V to 5.5V. Low-current design permits operation with typical standby and active currents of only 500 nA and 375 ?A, respectively. The MCP3202 is offered in 8-pin MSOP, PDIP, TSSOP and 150 mil SOIC packages.
Part Number:MCP3202-BI/P
Manufacturer:Microchip Technology
Description:IC ADC 12BIT SAR 8DIP
Detailed Description: 12 Bit Analog to Digital Converter 1, 2 Input 1 SAR 8-PDIP
MCP3202-BI/P Datasheet
MCP602-I/P
? Single-Supply: 2.7V to 6.0V
? Rail-to-Rail Output
? Input Range Includes Ground
? Gain Bandwidth Product: 2.8 MHz (typical)
? Unity-Gain Stable
? Low Quiescent Current: 230 ?A/amplifier (typical)
? Chip Select (CS): MCP603 only
? Temperature Ranges:
- Industrial: -40?C to 85?C
- Extended: -40?C to 125?C
? Available in Single, Dual, and Quad
N79E352RADG Nuvoton Microcontroller
N79E352(R) is an 8-bit Turbo 51 microcontroller which has Flash EPROM programmable hardware writer. The instruction set of the N79E352(R) is fully compatible with the standard 8052. The N79E352(R) contains a 8Kbytes of main Flash EPROM; a 256 bytes of RAM; 128 bytes NVM Data Flash EPROM; three 16-bit timer/counters; 2-channel 8-bit PWM; 1-channel UART and 1 additional input capture. These peripherals are supported by 11 interrupt sources four-level interrupt capability.
To facilitate programming and verification, the Flash EPROM inside the N79E352(R) allows the program memory to be programmed and read electronically. Once the code is confirmed, the user can protect the code for security. N79E352(R) is designed for cost effective applications which can serve industrial devices, and other low power applications.
- Part Number: N79E352RADG-ND
- Manufacturer: Nuvoton Technology Corporation
- Description: IC MCU 8BIT 8KB FLASH 40DIP
- Detailed Description: 8051 N79 Microcontroller IC 8-Bit 24MHz 8KB (8K x 8) FLASH
PIC16F877A Microcontroller
PIC16F877A is the most commonly used entry-level?8-bit PIC Microcontroller. It is a 40-pin 8-bit Microcontroller with 14kB of program memory. It does not have an internal oscillator but can work up to 20MHz with external oscillators. The controller has 8 ADC channels with 10-bit resolution and also supports PWM on 2 pins. It has two 8-bit timers and one 16-bit timer and supports communication protocols like UART, SPI, and IIC. You can also check other?PIC microcontroller?Components.
Reviews
There are no reviews yet.