MAX3232 RS-232 Line Driver
₹177.00
The?MAX3232 device?consists of two line drivers, two line receivers, and a dual charge-pump circuit with ?15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector.? The devices operate at data signaling rates up to 250 kbit/s and a maximum of 30-V/?s driver output slew rate.
1000 in stock (can be backordered)
Reviews (0)
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
AM26C32 Differential Line Receiver (SOIC)
AM26C32 is an improved replacement for?AM26LS32 IC. The AM26C32 device is a quadruple differential line receiver for balanced or unbalanced digital data transmission. The enable function is common to all four receivers and offers a choice of active-high or active-low input. The 3-state outputs permit connection directly to a busorganized system. Fail-safe design specifies that if the inputs are open, the outputs always are high. The AM26C32 devices are manufactured using a BiCMOS process, which is a combination of bipolar and CMOS transistors.
CM8870-PI
The CM8870PI provides full DTMF receiver capability by integrating both the bandsplit filter and digital decoder functions into a single 18-pin DIP. The filter section uses a switched capacitor technique for both high and low group filters and dial tone rejection. The CM8870 decoder uses digital counting techniques for the detection and decoding of all 16 DTMF tone pairs into a 4-bit code. This DTMF receiver minimizes external component count by providing an on-chip differential input ampli-fier, clock generator, and a latched three state interface bus. The on-chip clock generator requires only a low cost TV crystal or ceramic resonator as an external component.
CP2103 USB to TTL Converter
The CP2103 is a highly-integrated?USB-to-UART Bridge Controller?providing a simple solution for updating RS-232/RS-485 designs to USB using a minimum of components and PCB space. The CP2103 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, EEPROM, and asynchronous serial data bus (UART) with full modem control signals in a compact 5x5 mm QFN-28 package (sometimes called ?MLF? or ?MLP?). No other external USB components are required.
LM2596S 3.3 Volts fixed Voltage Converter (TO-263)
The LM2596S series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 1 Ampere load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5V, 12V, and an adjustable output version.
Requiring a minimum number of externalcomponents, these regulators are simple to use andinclude internal frequency compensation, and a fixed frequency oscillator.
Reviews
There are no reviews yet.