MOC7811 Slotted Opto Isolator Module
₹26.00
Performs Non-Contact Object Sensing. This is normally used as positional sensor switch (limit switch) or as Position Encoder sensors used to find position of the wheel.?MOC7811?consists of IR LED and Photodiode mounted facing each other enclosed in plastic body.
1000 in stock (can be backordered)
Reviews (0)
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
CH340g USB to TTL IC
As of now the CH340g is the cheapest USB to TTL IC in the market with very easy to solder foot print it has solder pitch of 1.27mm and SOIC16 package.
The?CH340 IC?does exactly what you would expect them to do: a full-speed USB device that emulates a standard serial interface, with speeds from 50bps to 2Mpbs. The chip supports 5V and 3.3V, and all the weird modem lines are supported.
Now a days lots of Node MCU, Arduino Nano and USB to TTL Converter Modules have been using this IC.
CM8870-PI
The CM8870PI provides full DTMF receiver capability by integrating both the bandsplit filter and digital decoder functions into a single 18-pin DIP. The filter section uses a switched capacitor technique for both high and low group filters and dial tone rejection. The CM8870 decoder uses digital counting techniques for the detection and decoding of all 16 DTMF tone pairs into a 4-bit code. This DTMF receiver minimizes external component count by providing an on-chip differential input ampli-fier, clock generator, and a latched three state interface bus. The on-chip clock generator requires only a low cost TV crystal or ceramic resonator as an external component.
CP2103 USB to TTL Converter
The CP2103 is a highly-integrated?USB-to-UART Bridge Controller?providing a simple solution for updating RS-232/RS-485 designs to USB using a minimum of components and PCB space. The CP2103 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, EEPROM, and asynchronous serial data bus (UART) with full modem control signals in a compact 5x5 mm QFN-28 package (sometimes called ?MLF? or ?MLP?). No other external USB components are required.
FT232 USB UART IC
Features of FT232
-
Single chip USB to asynchronous serial data transfer interface.
-
Entire USB protocol handled on the chip. No USB specific firmware programming required.
-
Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
-
Fully integrated USB termination resistors.
-
Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
-
Data transfer rates from 300 baud to 3 Mbaud (RS422, RS485, RS232) at TTL levels.
-
128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
LM2596S 3.3 Volts fixed Voltage Converter (TO-263)
The LM2596S series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 1 Ampere load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5V, 12V, and an adjustable output version.
Requiring a minimum number of externalcomponents, these regulators are simple to use andinclude internal frequency compensation, and a fixed frequency oscillator.
LM2596S 5 Volts fixed Voltage Converter (TO-263)
The LM2596 series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 1 Ampere load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5V, 12V, and an adjustable output version.
Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation, and a fixed frequency oscillator.
LM2596S Adjustable Voltage Converter (TO-263)
The LM2596S series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 1 Ampere load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5V, 12V, and an adjustable output version.
Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation, and a fixed frequency oscillator.
Reviews
There are no reviews yet.