TB6560AHQ – TOSHIBA BiCD Integrated Circuit
₹650.00
TB6560AHQ is a PWM chopper-type stepping motor driver IC designed for sinusoidal-input microstep control of bipolar stepping motors. The TB6560AHQ/AFG can be used in applications that require 2-phase, 1-2-phase, 2W1-2-phase, and 4W1-2-phase excitation modes. The TB6560AHQ/AFG is capable of low-vibration, high-performance forward and reverse driving of a two-phase bipolar stepping motor using only a clock signal.
Mfr. No:TB6560AHQ,8
Mfr.:Toshiba
Description: Motor/Motion/Ignition Controllers & Drivers Stepping Motor Driver IC
Datasheet:TB6560AHQ,8 Datasheet (PDF)
500 in stock
Description
TB6560 Stepping Motor Driver ICs
Toshiba TB6560 Stepping Motor Driver ICs are designed for sinusoidal input micro-step control of stepping motors. These ICs are capable of forward and reverse driving of a two-phase bipolar stepping motor using only a clock signal. The TB6560 ICs are used in applications that require 2-phase, 1-2-phase, 2W1-2-phase, and 4W1-2-phase excitation modes. These motor driver ICs offer high output withstand voltage (40V) due to BiCD process. The ICs feature reset and enable pins.
TOSHIBA BiCD Integrated Circuit – These ICs are highly sensitive to electrostatic discharge. When handling them, ensure that the environment is protected against electrostatic discharge. Ensure also that the ambient temperature and relative humidity are
maintained at a reasonable level.
Features : TB6560AHQ – TOSHIBA IC’s
- Single-chip motor driver for sinusoidal micro-step control of stepping motors
- High output withstands voltage due to the use of BiCD process: Ron (upper and lower sum) =
TB6560AHQ: 0.6 ? (typ.)
TB6560AFG: 0.7 ? (typ.) - Forward and reverse rotation
- Selectable phase excitation modes (2, 1-2, 2W1-2 and 4W1-2)
- High output withstand voltage: VDSS = 40 V
- High output current: IOUT = TB6560AHQ: 3.5 A (peak)
TB6560AFG: 2.5 A (peak) - Packages: HZIP25-P-1.27
HQFP64-P-1010-0.50 - Internal pull-down resistors on inputs: 100 k? (typ.)
- Output monitor pin: MO current (IMO (max) = 1 mA)
- Reset and enable pins
- Thermal shutdown (TSD)
Specifications – TB6560AHQ – TOSHIBA IC’s
- Manufacturer – TOSHIBA
- Type of integrated circuit – driver
- Kind of integrated circuit – stepper motor controller
- Interface – PWM
- Case – SIP25
- Output current – 3A
- Output voltage – 4.5…34V
- Number of channels -2
- Mounting – THT
- Operating temperature – -30…85?C
- Input voltage – 0…5.5V
- Additional information – Gross weight: 9.72 g
- Manufacturer part number: TB6560AHQ
Reviews (0)
Shipping & Delivery
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
Related products
LNK304PN IC – Power Integrations – AC-DC Off Line Switcher IC
The LNK304PN is specifically designed to replace all linear and capacitor-fed (cap dropper) non-isolated power supplies in the under 360 mA output current range at equal system cost while offering much higher performance and energy efficiency. LinkSwitch-TN devices integrate a 700 V power MOSFET, oscillator, simple On/Off control scheme, a high-voltage switched current source, frequency jittering, cycle-by-cycle current limit Figure 1. Typical Buck Converter Application (See Application Examples Section ? ?for Other Circuit Configurations).and thermal shutdown circuitry onto a monolithic IC. The start-up and operating power are derived directly from the voltage on the DRAIN pin, eliminating the need for a bias supply and associated circuitry in buck or fly back converters. The fully integrated auto-restart circuit in the LNK304 safely limits output power during fault conditions such as short-circuit or open loop, reducing component count and system-level load protection cost. ?A local supply provided by the IC allows use of a non-safety graded optocoupler acting as a level shifter to further enhance line and load regulation performance in buck and buck-boost converters.
LNK305PN IC – Power Integrations – AC-DC Off Line Switcher IC
The LNK305PN is specifically designed to replace all linear and capacitor-fed (cap dropper) non-isolated power supplies in the under 360 mA output current range at equal system cost while offering much higher performance and energy efficiency. LinkSwitch-TN devices integrate a 700 V power MOSFET, oscillator, simple On/Off control scheme, a high-voltage switched current source, frequency jittering, cycle-by-cycle current limit Figure 1. Typical Buck Converter Application (See Application Examples Section ? ?for Other Circuit Configurations).and thermal shutdown circuitry onto a monolithic IC. The start-up and operating power are derived directly from the voltage on the DRAIN pin, eliminating the need for a bias supply and associated circuitry in buck or fly back converters. The fully integrated auto-restart circuit in the LNK305 safely limits output power during fault conditions such as short-circuit or open loop, reducing component count and system-level load protection cost. ?A local supply provided by the IC allows use of a non-safety graded optocoupler acting as a level shifter to further enhance line and load regulation performance in buck and buck-boost converters.
LNK306PN IC – Power Integrations – AC-DC Off Line Switcher IC
The LNK306PN is specifically designed to replace all linear and capacitor-fed (cap dropper) non-isolated power supplies in the under 360 mA output current range at equal system cost while offering much higher performance and energy efficiency. LinkSwitch-TN devices integrate a 700 V power MOSFET, oscillator, simple On/Off control scheme, a high-voltage switched current source, frequency jittering, cycle-by-cycle current limit Figure 1. Typical Buck Converter Application (See Application Examples Section ? ?for Other Circuit Configurations).and thermal shutdown circuitry onto a monolithic IC. The start-up and operating power are derived directly from the voltage on the DRAIN pin, eliminating the need for a bias supply and associated circuitry in buck or fly back converters. The fully integrated auto-restart circuit in the LNK306 safely limits output power during fault conditions such as short-circuit or open loop, reducing component count and system-level load protection cost. ?A local supply provided by the IC allows use of a non-safety graded optocoupler acting as a level shifter to further enhance line and load regulation performance in buck and buck-boost converters.
LNK419EG IC – Power Integrations – LED Driver Off Line Switcher IC
The LNK419EG dramatically simplifies implementation of LED drivers requiring long lifetime, high efficiency, PF >0.9, and TRIAC dimming capability(LNK403-410). The single-stage combined power factor and constant-current controller eliminates a switching stage and the electrolytic bulk capacitor. ?The advanced primary-side control used by the LNK419EG device provides accurate constant current control while eliminating the need for an optocoupler and current sensing circuits .LinkSwitch-PH incorporates a 725 V power FET, a continuous-mode PWM controller, a high-voltage switched current source for self biasing, frequency jittering, protection circuitry including cycle-by-cycle current limit and hysteretic thermal shutdown.
TOP244YN IC – Power Integrations – Off Line Switcher IC
TOP244YN belongs to TOPSwitch-GX Family from the manufacturer "Power Integrations". It is with Extended Power, Design Flexiblity, EcoSmart & Integrated Off-line Switcher. TOPSwitch-GX uses the same proven topology as TOPSwitch, cost effectively integrating the high voltage power MOSFET, PWM control, fault protection and other control circuitry onto a single CMOS chip. Many new functions are integrated to reduce system cost and improve design flexibility, performance and energy efficiency. Depending on package type, either 1 or 3 additional pins over the TOPSwitch standard DRAIN, SOURCE and CONTROL terminals allow the following functions: line sensing (OV/UV, line feed-forward/DCMAX reduction), accurate externally set current limit, remote ON/OFF, synchronization to an external lower frequency, and frequency selection (132 kHz/66 kHz). All package types provide the following transparent features: Soft-start, 132 kHz switching frequency (automatically reduced at light load), frequency jittering for lower EMI, wider DCMAX, hysteretic thermal shutdown, and larger creepage packages. In addition, all critical parameters (i.e. current limit, frequency, PWM gain) have tighter temperature and absolute tolerances to simplify design and optimize system cost.
TOP248YN IC – Power Integrations – Off Line Switcher IC
TOP248YN belongs to TOPSwitch-GX Family from the manufacturer "Power Integrations". It is with Extended Power, Design Flexiblity, EcoSmart & Integrated Off-line Switcher. TOPSwitch-GX uses the same proven topology as TOPSwitch, cost effectively integrating the high voltage power MOSFET, PWM control, fault protection and other control circuitry onto a single CMOS chip. Many new functions are integrated to reduce system cost and improve design flexibility, performance and energy efficiency. Depending on package type, either 1 or 3 additional pins over the TOPSwitch standard DRAIN, SOURCE and CONTROL terminals allow the following functions: line sensing (OV/UV, line feed-forward/DCMAX reduction), accurate externally set current limit, remote ON/OFF, synchronization to an external lower frequency, and frequency selection (132 kHz/66 kHz). All package types provide the following transparent features: Soft-start, 132 kHz switching frequency (automatically reduced at light load), frequency jittering for lower EMI, wider DCMAX, hysteretic thermal shutdown, and larger creepage packages. In addition, all critical parameters (i.e. current limit, frequency, PWM gain) have tighter temperature and absolute tolerances to simplify design and optimize system cost.
Reviews
There are no reviews yet.